I have the Ozone Maximiser set to to True Peak -1.3 dB. The outputs are set to about -15 to -17 dB overall in Insight. Once I have this set I’ll check that Insight is where I want it and make adjustment usually just the level of the Maximiser in Ozone. I’ll check the Tonal Balance Control and make adjustments usually to Ozone (I might add the “Low End Focus” or whatever). Once I have the mix sounding how I like I run Ozone - Master Assistant. This now sets the volume, width and position of each track. At this point I’ll move the individual tracks using the Visual Mixer. Once I’ve gone through that process I’ll add my “mastering” FX Chain onto the master track.Īdding the master adds the Visual Mixer, Ozone 9, Tonal Balance Control and Insight 2. This could include Spectra Edits or whatever to clean up the song and get it how I want. I might move parts or cut and paste set trims to get the track how I want. I use the area I expect to be the loudest part (usually looping the area where the instrumental part of the song is set in the markers). I then run Neutron Assistant to get a start on setting each track then maybe a little tweaking. This all delivers a consistent starting point. I play the track through adding markers for parts (also colour coded for ease) This all usually takes about 5 mins plus the time playing the song. I sort the order of and name the tracks once again the colouring of tracks is automated based on the name. I then put Neutron on every track using another setup keystroke. In Reaper I have set up a short cut key so it is a simple matter of selecting all tracks and pressing. In Reaper (or Cakewalk) after pulling the tracks in I normalise all tracks to -12 dB this gives me a starting point where everything is even. (And lately mono) Then I pull then into a daw (usually Reaper) for mixing. The instructions in this tutorial will work in the following model years:Ģ004, 2005, 2006, 2007, 2008, 2009, 20 – Audi A6 C6 Petrol (2.0 TFSI, 2.4 Quattro, 2.4 V6, 2.8 FSI, 3.3 Quattro, 3.2 V6, 4.2 V8, 4.2 V8 Quattro and S6) and Diesel (2.0 and 2.7 TDI, 2.7 V6 and 3.0 V6) Engines.I tend to export all tracks flat and centred. Intelligent power module rear (lights left-side) Intelligent power module rear (lights right-side) Audi A6 C6 – Fuse Box Diagram – Luggage Compartment rightĭigital Signal Processing (DSP)/ BOSE amplifier To access the fuse box located on the luggage compartment you should remove the right side trunk trim and open the fuse cover. Shift gate automatic transmission/clutch switchĪutomatic headlight range control (auxiliary driving lights), headlight electronics, right-sideģ- Fuse box in the Luggage Compartment right Audi A6 C6 – Fuse Box Diagram – Dashboard passenger’s side To access the fuse box located on the passenger’s side of the dashboard, you must have the passenger’s door open and remove the side dash cover. Intelligent power module driver (lights right-side)Ĭontrol module electronic ignition lock/electrically adjustable steering wheelĢ- Fuse box in the Dashboard passenger’s side Intelligent power module driver (lights left-side) Intelligent power module driver (footwell light and front headlights, horn, wiper system, electrically adjustable steering wheel) Instrument cluster, control module Gatewayīack-up light switch, transmission, engine components Audi A6 C6 – Fuse Box Diagram – Dashboard driver’s sideĬlimate control, tire pressure monitoring systemĮlectronic Stabilization Program (ESP), clutch You will also find a label on both covers in the instrument panel with the fuse layout (C) for the corresponding fuse panel. The crank (B) is used for emergency operation of the power roof. There is a plastic clip (A) in the cover on the left side of the instrument panel, which can be used to remove the fuses. To access the fuse box located on the driver’s side of the dashboard, open the driver’s door and remove the plastic clip (A) from its retainer in the face cover. Two on dashboard passenger and driver side and one in the luggage compartment – Scroll down to see how to access them and the fuses list.ġ- Fuse box in the Dashboard driver’s side The Audi A6 C6, Audi A6 C6 allroad, Audi A6 C6 Avant and Audi A6L C6 (2004 – 2011) have 3 fuse boxes location.
0 Comments
Leave a Reply. |